Titan-tool 800-2005 Uživatelský manuál

0104 © 2004 Titan Tool Inc. All rights reserved. Form No. 313-2384, REV APrinted in the U. S. A.Do not use this equipment before reading this manual

Replacing the Transducer1. Unplug the unit.2. Loosen and remove the four motor shroud screws.Remove the motor shroud.3. At the electronic control asse

Repacking the Fluid Section1. Remove the foot valveassembly and the lowerhousing using the steps in the“Servicing the Valves”procedure above.2. Slide

Solution1. Check2. Increase3. Replace4. Replace5. Reset the breaker1. Check siphon tube o-ring and/or let paintcirculate in prime position2. Increase

©Titan Tool Inc. All rights reserved. 13TroubleshootingSpray PatternsProblemTailsHeavy centered patternDistorted patternPattern expanding andcontract

14 ©Titan Tool Inc. Tous droits réservés.Consignes de sécuritéLe présent manuel comprend des renseignements devant êtrelus attentivement avant toute

©Titan Tool Inc. Tous droits réservés. 15MOTEUR À ESSENCE (DANS LES CAS OÙ CELA S’APPLIQUE)Toujours placer la pompe à l’extérieur de la structure à l

16 ©Titan Tool Inc. Todos los derechos reservados.Precauciones de seguridadEste manual contiene información que debe leer y comprenderantes de usar e

©Titan Tool Inc. Todos los derechos reservados. 17PELIGRO: PELIGRO DE EXPLOSIÓN DEBIDO AMATERIALES INCOMPATIBLES - Podríacausar lesiones severas o

18 © Titan Tool Inc. All rights reserved.Parts List Main Assembly126731314598101112415161819202117Item Part # Description Quantity1 800-600 Cart asse

©Titan Tool Inc. All rights reserved. 19Item Part # Description Quantity1 800-078 Electronic cover ...12 800-2

Table of ContentsSafety Precautions...2Français ...

20 © Titan Tool Inc. All rights reserved.Fluid Section Assembly (P/N 800-300)15101317181920782178911121415166324Install lower packing with the side t

©Titan Tool Inc. All rights reserved. 21Item Part # Description Quantity1 800-325 Upper seal retainer ...12 800-327

22 © Titan Tool Inc. All rights reserved.Low Rider Cart (P/N 800-590)12345678910111213161514ItemPart # Description Quantity1 590-506 Washer...

©Titan Tool Inc. All rights reserved. 23AccessoriesAirless Tip SelectionTips are selected by the orifice size and fan width. The properselection is

24 © Titan Tool Inc. All rights reserved.United States Sales & Service1-800-526-5362Fax 1-800-528-4826107 Bauer DriveOakland, NJ 07436www.titanto

GAS ENGINE (WHERE APPLICABLE)Always place sprayer outside of structure in fresh air. Keep allsolvents away from engine exhaust. Never fill fuel tank

General DescriptionThis airless sprayer is a precision power tool used for sprayingmany types of materials. Read and follow this instructionmanual ca

7. Move the PRIME/SPRAY valve up to the SPRAY position.8. Turn the unit on and set the pressure to minimum byturning the pressure control knob to the

Solid YellowWhen the pressure indicator is solid yellow, the sprayer isoperating between 200 and 1800 PSI. A solid yellow pressureindicator means:•Th

For corners and edges, split thecenter of the spray pattern on thecorner or edge and spray verticallyso that both adjoining sectionsreceive approximat

2. Test your repair before regular operation of the sprayer tobe sure that the problem is corrected. If the sprayer doesnot operate properly, review

Replacing the Motor Assembly(with Electronic Control)1. Unplug the unit.2. Loosen and remove the four motor shroud screws.Remove the motor shroud.3. R